| The 007 logo this went on the grip cap of a K-80 - It was designed and engraved it into Stainless Steel, It was sealed during the finish process to keep it nice |
 |
The Sub-Mariner Badge This is an exact replica of the badge that was given to servicemen that served during war time under the water for extended amounts of time |
 |
| The Cobra This was engraved directly into the Ebony Grip Cap. The customer chose the design and this was the finished product. It is sealed to preserve the integrity |
 |
Eric Weikum This was a very special project in honor of Eric. The badge bares his foundation and it is embedded into the back side of an adjustable comb built for a high rib Gun. |
 |
| Oak & Ebony This was a feature for a special edition that the guys in the shop made. The stock was burl Pin Oak from Ernie Ross and the grip is made of Oak and Ebony bonded together |
 |
Viva Las Vegas A special project done for Steph Carmichael Steph did the design and Cindy hand checkered the Hearts, Spades, Diamonds & Clubs to give the forend a real Vegas look |
 |
| Vegas In keeping with the theme Cindy laid out the dice, cut the outline in the Ebony Grip Cap & then hand painted the outline. The grip was sealed to preserve the integrity of the work.
|
 |
Infinity This design is the Greek symbol and was installed in black Ebony. The part was done in steel, sent out for gold plating & sealed into the grip during the finish process
|
 |
| Black Diamonds We were asked to install a Black Ebony Diamond in the upper grip of a Ljutic stock. The diamonds were cut on the NC machine and install prior to the final finish was applied |
 |
Black Diamonds Again the Ebony Diamonds were installed on both sides of the grip to finish the request. |
 |
| Black Diamond & Ebony Bill Mains did the engraving and we were asked to imbed the badge into the Ebony grip & seal it to keep out of harms way
|
 |
Special Forces This was a special project as well. The badge was presented to us from an Ex Special Forces Army Ranger. It was a little tricky but we were able to fill in the voids and seal it in the grip to be preserved forever |
 |
| Full Bird Wings This is a set of Full Bird Wings for a Colonel in the US Air Force that had a stock built for a Perazzi MX-2000 Combo the wings were set into an Ebony Grip Cap &sealed to preserve the integrity |
 |
Seize The Moment This was done in the Ebony grip using a brass engraved that we did here and setting the ATA pin in the center. It was then sealed to preserve the integrity of the piece |
 |
| The Maple Leaf Cindy did the layout and design of the Maple Leaf for a Canadian Sporting Clays shooter that had a custom Stock & forend done here The gun was a Perazzi low rib MX-2000 |
 |
The Corn Grip Our customer requested an ear of corn to be engraved into a piece of Brass and then inserted in the bottom of the grip of the gun
|
 |
| Veterinary Symbol Brian really out did himself with this latest creation, the part was made in 3-D, the brass emblem was sunk below the surface after it was inserted, then it was covered to preserve the integrity of the piece |
 |
MX- 2000 Perazzi Gold Coin this is a gold coin given to a shooter from his father. He wanted to keep his father's memory close by when shooting so the coin was placed in the grip cap of the gun. A very special tribute |
 |
| The Pineapple This was requested and done on an Ebony Grip Cap for a Krieghoff K-80 Sporting Clays Gun |
 |
||
| Checkering Cheeks This is an additional cost when refinishing a stock is done. The cost is $ 150.00 |
 |
Signature Black Ebony Grip Cap This is a $ 175.00 additional cost when getting a Custom Gunstock or refinish work. |
 |